11/12/2023 0 Comments Seatool SeagateWe eventually had to abort the test, which caused the program to freeze and shut down. The Long Drive Self Test, however, never progressed past a certain point. The Short Drive Self Test had the same outcome. The program quickly scanned our drive, and it passed the test, but that's all we know SeaTools doesn't display scan results. We went through each test that the program offered, starting with the S.M.A.R.T. It detected our only drive, along with its serial number, model number, firmware revision, and drive and test status. SeaTools' user interface is extremely stark: basic menu items line the top of a plain window, with detected drives are listed below. You'll have to take its word that it's working, though, because it doesn't offer any scan details. To reset the drive to its full capacity, run SeaTools' Set Capacity feature and select R to reset the drive to its maximum capacity.Īlways backup information on a drive that you are changing the size of, as it is a potentially data-destructive process, even if you are changing the setting from a smaller to a larger size.įor more detailed information on using SeaTools for DOS to set drive capacity, please see Document ID: 203451.Hard disk maker Seagate's SeaTools for Windows scans your disk drives for driver corruption, broken master boot records, viruses and Trojans, spyware, and any hardware conflicts. Check with your motherboard or system manufacturer. You may need a BIOS upgrade or ATA PCI controller card if the system continues to freeze, hang, or lockup during startup. This is critical in order for the changes to take effect to the drive.Ĭhange the BIOS parameters from "None" to "Auto-Detect".īoot to your operating system installation CD / DVD and begin the installation of your operating system. Once you have changed the capacity for the drive and SeaTools for DOS accepts it, power off the system. If you do know the maximum, you can press M to set the limit manually. If you don't know the maximum capacity drive your system's BIOS can handle, press S to set the maximum to 32GB, which is a common limit on older systems. When the system boots to the SeaTools program, select the drive you want to change the size of, and press C to set the drive capacity. Power on and boot directly to the SeaTools for DOS CD or floppy diskette. Reconnect the drive to the port that is configured as None or Not-Installed. This will tell the BIOS that there is no device or drive attached to the port. Set the BIOS parameters (example: Primary Master, Primary Slave, Secondary Master, or Secondary Slave) to where the drive is connected from Auto-Detect to None or Not-Installed. If there is data on the drive, please format the drive or use SeaTools for DOS' Zero-Fill utility.įollow the steps below to ensure that the Set Capacity operation is properly run: Changing a drive size to a smaller capacity is a data-destructive process. If your hard drive is seen in the BIOS as 137GB and you are installing Windows 2000 with Service Pack 3 or greater, Windows XP with Service Pack 1 or greater, or Windows Vista, you shouldn't need to set the hard drive size, as the current versions of those operating systems should bypass any BIOS limitations on the driveĭo not try to resize a drive that has data on it. Because of this, the Set Capacity feature will not work on any SATA hard drive. If you are using a SATA drive, you do not need to change what capacity is reported to the BIOS, as the specifications for SATA controllers were designed with larger-capacity drives in mind. The BIOS on the ATA PCI card should recognize the full capacity of the drive. If you are using an add-on ATA PCI adapter card, do not use this utility. This procedure applies only to ATA drives connected directly to the motherboard. Instead, it is highly recommended you either update your system's BIOS or purchase an ATA PCI controller card to bypass your system's BIOS. Please be aware that the "Set Hard Drive Size" feature is no longer available in the current versions of MaxBlast and DiscWizard, so you will have to use SeaTools for DOS instead to set the hard drive's capacity.įollowing this procedure will allow you to access your hard drive however you won't be able to use the full capacity. The feature allows older systems with a BIOS limitation to boot with the drive in the system instead of locking up or freezing during the boot process. The ability to "Set Capacity" is a feature in SeaTools for DOS that will instruct the selected hard drive to report a size smaller than its true capacity during boot.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |